CISCO MDS 9124 CONFIGURATION GUIDE PDF

Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Kazicage Mazugore
Country: Comoros
Language: English (Spanish)
Genre: Love
Published (Last): 28 February 2016
Pages: 34
PDF File Size: 19.25 Mb
ePub File Size: 17.16 Mb
ISBN: 403-6-60051-652-7
Downloads: 95409
Price: Free* [*Free Regsitration Required]
Uploader: Tojagami

This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator. About System Message Confoguration properly configured system message logging server. Then states two bullets later: Page Information is repeated twice on the same page: This is configuratin correct as this does not work. Certainly there is either a mistake in the wording or the example.

It is worded as if it is a requirement but it is in fact not. Should be 8 base ports, which can goto 8 or 16 additional ports. I am not sure that the statement in bold is correct.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

On the same page I find this block of text very vague and confusing: This is not true. The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer. Should say Step 1 Gudie the mgmt 0 interface. Although it can be configured it has no effect.

  FOWLES AND CASSIDAY ANALYTICAL MECHANICS SOLUTIONS PDF

Guife a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur.

Page Document states: Reconfiguration as in changing of domains is always disruptive. Previous blog entries also dealt with storage, compute, virtualization and professional services.

This situation can require several configuration tasks for each iSCSI host. From time to time I will blog about other things of interest. I am not sure.

Page Figure shows incorrect ip default-gateway Page States in one bullet: This should be made more clear. Page shows with 8 base ports 8 licensed for growth. You basically give the same settings for the IBM blade switch but this is cconfiguration 24 port not a 20 port. When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: IP routing does not have to be enabled, unless there is a specific topology where IP routing is necessary.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

Proudly powered by WordPress. This blog is mostly about my pursuits in Data Configurahion. I think what is meant here is: You must be logged in to post a comment. This page incorrectly states that you can disable password verification with aaa authentication login none command. This is not correct.

  LA SACRA BIBBIA LUZZI PDF

This can mean several configuration tasks for each iSCSI host. This is very redundant and can be combined into one bullet. Obviously there was a part of this paragraph that got chopped off somewhere. A disruptive reconfiguration may affect data confihuration.

If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration. This page incorrect states that fcns reject-duplicate-pwwn configguration disabled by default. The default authentication port is Testing indicates that this is in fact enabled by default. In this case, using the proxy initiator mode simplifies the configuration.

You do not need to restart the fcdomain. FCIP uses different ports.

You cannot mix ingress and egress interfaces in the same SPAN session. Cisco Documentation team has internally re-written this as: The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.

Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch. Icsco pages talk about an active mode of fcanalyzer.

If you assign port number for physical portshow can you assign for ports ? I am not sure if this is valid.