transformer, test leads, and input jacks — must be purchased from Keithley Instruments. Standard fuses with For analog filter (Models A/A only) . leaving the factory the A and A meet these specifications. the Series A Reference Manual for additional power derating. Keithley A Pdf User Manuals. View online or download Keithley A User Manual.

Author: Shaktile Nazil
Country: Fiji
Language: English (Spanish)
Genre: Travel
Published (Last): 9 November 2004
Pages: 83
PDF File Size: 16.25 Mb
ePub File Size: 17.33 Mb
ISBN: 253-6-65584-527-4
Downloads: 76736
Price: Free* [*Free Regsitration Required]
Uploader: Mazutaur

Instrument programming When you create a script using script.

The cyclic voltammetry, iv and it curves are collected with a keithley source measure unit a, keithley instruments, cleveland, ohio. Front Panel Summaries Instrument programming Resetting the password If you forget the password, you can reset the password from the front panel.

Under Construction:

TSP command reference Also see Bit manipulation and logic operations on page bit. All trigonometric functions work in radians.

Make A Measurement In addition to the default buffers, you can create user-defined reading buffers. To set more than one bit of the register, set standardRegister to the sum of their decimal weights.

Maunal source autorange 1 or smuX. Instrument programming Lua memory management Lua automatically manages memory, which means you do not have to allocate memory for new objects and free it when the objects are no longer needed. It does not affect the smuX.

Displays the primary limit setting 1 or display. The keysight a is fully tested and refurbished in our in.

C Confirming port numbers The only time a script is aborted is when a Lua run-time error errorerrorerror code”TSP runtime error” is detected. Functions and features You can obtain very precise timing and synchronization between channels of multiple instruments using the trigger model to control the actions of the source-measure unit SMU.


Provides unpacking instructions, describes basic connections, and reviews basic operation information.

Keithley have variety of smus for different use requirements. Product specifications are subject to change. For example, to access status keitlhey for the second element of SMU channel A buffer 1, use the following command: To delete a script from TSB embedded: If Test2 is selected, the message Running Test2 is displayed. The Select Instrument Driver dialog box is displayed. Measurements are made at the end of keithlfy ton time. It also creates a global variable with the same name as the name of the script.

It is typically set to the date when the next calibration should be performed. If the trigger count is greater than the number of points specified, the SMU will start over at the beginning value.

Disables high-capacitance mode 1 or smuX. Reading a status register returns a value. Install oeithley tighten the screws securely, making sure not to overtighten them.

Keithley A Manuals

Both of the following figures depict the effect keithleyy the asymptote on the inflection of the sweep curve. TSP command reference script. If the programmed state of the line is high, the digio. The example configures the timers and SMU as follows: In general, these steps are: Front And Rear Panel Operation There amnual three primary factors that affect measurement accuracy and speed: Using the termSequence parameter sets the termination sequence.


Functions and features The sweep can be either positive-going or negative-going, depending on the relative values of the start and stop parameters. If the output line is write-protected by the tsplink. To ensure accuracy of readings, the instrument must periodically obtain fresh measurements of its internal ground and voltage reference.

Local area network LAN communications provide the flexibility to build scalable and functional test or data acquisition systems with a large degree of flexibility. Step-by-step procedures and connection diagrams for verifying the manyal measurement accuracy for the low current ranges are included with the Model STD-RES.

Do not use this command to retrieve the value of a global variable from the local node.

Keithley 2636A Manuals

Note that you must send lan. When a script is named, it can be accessed using the global variable scriptVar. Turn Off The Output If this step is not on the CALA sense mode, send the measure calibration 236a using the multimeter and Series B readings, and the range setting for the parameters. Refer to notes in the b reference manual for additional details. Manuzl Channel A buffer. To delete a script from nonvolatile memory using a remote interface: To set the source range and output value: